Support for Policy Priority Was Introduced > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

The Switch Integrated Security Features based (SISF-based) device tracking characteristic is part of the suite of first-hop safety features. The primary position of the characteristic is to trace the presence, location, and movement of end-nodes in the community. SISF snoops traffic received by the switch, extracts system identity (MAC and smart key finder IP handle), and stores them in a binding table. Many options, similar to, IEEE 802.1X, internet authentication, Cisco TrustSec and LISP and many others., rely upon the accuracy of this data to function correctly. SISF-based machine tracking helps each IPv4 and best item finder gadget IPv6. Even with the introduction of SISF-based gadget monitoring, the legacy machine monitoring CLI (IP Device Tracking (IPDT) and smart key finder IPv6 Snooping CLI) continues to be available. The IPDT and iTagPro support IPv6 Snooping commands are deprecated, however proceed to be out there. We recommend that you improve to SISF-primarily based device tracking. If you're using the IPDT and smart key finder IPv6 Snooping CLI and need to migrate to SISF-based machine monitoring, see Migrating from legacy IPDT and IPv6 Snooping to SISF-Based Device Tracking, for more data.

SISF-primarily based system tracking can be enabled manually (through the use of device-monitoring commands), or programmatically (which is the case when offering system monitoring providers to other options). SISF-primarily based system monitoring is disabled by default. You'll be able to enable it by defining a system tracking coverage and attaching the policy to a selected target. The goal could be an interface or a VLAN. Option 1: Apply the default device tracking coverage to a target. Enter the machine-monitoring command in the interface configuration mode or within the VLAN configuration mode. The system then attaches the default policy it to the interface or VLAN. The default coverage is a constructed-in coverage with default settings; you cannot change any of the attributes of the default policy. So as to be able to configure gadget tracking coverage attributes you need to create a custom coverage. See Option 2: Create a custom policy with custom settings. Option 2: iTagPro key finder Create a customized coverage with custom settings. Enter the machine-monitoring policy command in global configuration mode and enter a custom policy name.

The system creates a coverage with the identify you specify. You may then configure the available settings, within the system tracking configuration mode (config-machine-monitoring), and attach the policy to a specified target. Some features rely on device monitoring and utilize the trusted database of binding entries that SISF-based machine monitoring builds and maintains. These options, also referred to as device monitoring clients, enable device monitoring programmatically (create and attach the device tracking coverage). The exceptions listed here are IEEE 802.1X, internet authentication, Cisco TrustSec, and IP Source Guard (IPSG) - additionally they depend on device monitoring, but they do not enable it. For these gadget tracking clients, you must enter the ip dhcp snooping vlan vlan command, to programmatically enable gadget tracking on a selected target. A machine tracking consumer requires machine tracking to be enabled. There are a number of device monitoring purchasers, subsequently, multiple programmatic insurance policies might be created. The settings of every coverage differ depending on the machine tracking shopper that creates the coverage.

The policy that is created, and smart key finder its settings, ItagPro are system-defined. Configurable policy attributes are available within the system tracking configuration mode (config-system-tracking) and fluctuate from one release to another. For those who try to change an attribute that isn't configurable, the configuration change is rejected and an error message is displayed. For extra information about programmatically created policies, see Programmatically Enabling SISF-Based Device Tracking in Cisco IOS XE Fuji 16.9.x and Later Releases. Based on the legacy configuration that exists on your machine, the device-monitoring upgrade-cli command upgrades your CLI otherwise. Consider the following configuration scenarios and the corresponding migration results earlier than you migrate your present configuration. You can't configure a mix of the previous IPDT and IPv6 snooping CLI with the SISF-primarily based device monitoring CLI. In case your system has solely IPDT configuration, operating the gadget-monitoring upgrade-cli command converts the configuration to make use of the new SISF coverage that's created and smart key finder connected to the interface.